Learn the UNIX/Linux command line
Home Man Pages
mformat(1) mformat(1)
Name
mformat - add an MSDOS filesystem to a low-level formatted floppy disk
Note of warning
This manpage has been automatically generated from mtools's texinfo
documentation, and may not be entirely accurate or complete. See the
end of this man page for details.
Description
The mformat command is used to add an MS-DOS filesystem to a low-level
formatted diskette. Its syntax is:
mformat [-t cylinders] [-h heads] [-n sectors]
[-f size] [-1] [-4] [-8]
[-v volume_label]
[-F] [-S sizecode] [-X]
[-2 sectors_on_track_0] [-3]
[-0 rate_on_track_0] [-A rate_on_other_tracks]
[-M software_sector_size]
[-N serial_number] [-a]
[-C] [-H hidden_sectors] [-I fsVersion]
[-r root_sectors] [-L fat_len]
[-B boot_sector] [-k]
drive:
Mformat adds a minimal MS-DOS filesystem (boot sector, FAT, and root
directory) to a diskette that has already been formatted by a Unix
low-level format.
The following options are supported: (The S, 2, 1 and M options may
not exist if this copy of mtools has been compiled without the USE_2M
option)
The following options are the same as for Dos's format command:
Options
v Specifies the volume label. A volume label identifies the disk
and can be a maximum of 11 characters. If you omit the -v
switch, mlabel will assign no label to the disk.
f Specifies the size of the DOS filesystem to format. Only a cer-
tain number of predefined sizes are supported by this flag; for
others use the -h/-t/-n flags. The following sizes are sup-
ported:
160 160K, single-sided, 8 sectors per track, 40 cylinders
(for 5 1/4 DD)
180 160K, single-sided, 9 sectors per track, 40 cylinders
(for 5 1/4 DD)
320 320K, double-sided, 8 sectors per track, 40 cylinders
(for 5 1/4 DD)
360 360K, double-sided, 9 sectors per track, 40 cylinders
(for 5 1/4 DD)
720 720K, double-sided, 9 sectors per track, 80 cylinders
(for 3 1/2 DD)
1200 1200K, double-sided, 15 sectors per track, 80 cylinders
(for 5 1/4 HD)
1440 1440K, double-sided, 18 sectors per track, 80 cylinders
(for 3 1/2 HD)
2880 2880K, double-sided, 36 sectors per track, 80 cylinders
(for 3 1/2 ED)
t Specifies the number of tracks on the disk.
h The number of heads (sides).
n Specifies the number of sectors per track. If the 2m option is
given, number of 512-byte sector equivalents on generic tracks
(i.e. not head 0 track 0). If the 2m option is not given, num-
ber of physical sectors per track (which may be bigger than 512
bytes).
1 Formats a single side (equivalent to -h 1)
4 Formats a 360K double-sided disk (equivalent to -f 360). When
used together with -the 1 switch, this switch formats a 180K
disk
8 Formats a disk with 8 sectors per track.
MSDOS format's q, u and b options are not supported, and s has a dif-
ferent meaning.
The following options are specific to mtools:
F Format the partition as FAT32.
S The sizecode. The size of the sector is 2 ^ (sizecode + 7).
X formats the disk as an XDF disk. See section XDF, for more
details. The disk has first to be low-level formatted using the
xdfcopy utility included in the fdutils package. XDF disks are
used for instance for OS/2 install disks.
2 2m format. The parameter to this option describes the number of
sectors on track 0, head 0. This option is recommended for sec-
tors bigger than normal.
3 don't use a 2m format, even if the current geometry of the disk
is a 2m geometry.
0 Data transfer rate on track 0
A Data transfer rate on tracks other than 0
M software sector size. This parameter describes the sector size
in bytes used by the MS-DOS filesystem. By default it is the
physical sector size.
N Uses the requested serial number, instead of generating one
automatically
a If this option is given, an Atari style serial number is gener-
ated. Ataris store their serial number in the OEM label.
C creates the disk image file to install the MS-DOS filesystem on
it. Obviously, this is useless on physical devices such as
floppies and hard disk partitions, but is interesting for image
files.
H number of hidden sectors. This parameter is useful for format-
ting hard disk partition, which are not aligned on track bound-
aries (i.e. first head of first track doesn't belong to the
partition, but contains a partition table). In that case the
number of hidden sectors is in general the number of sectors
per cylinder. This is untested.
I Sets the fsVersion id when formatting a FAT32 drive. In order
to find this out, run minfo on an existing FAT32 drive, and
mail me about it, so I can include the correct value in future
versions of mtools.
c Sets the size of a cluster (in sectors). If this cluster size
would generate a FAT that too big for its number of bits,
mtools automatically increases the cluster size, until the FAT
is small enough.
r Sets the size of the root directory (in sectors). Only appli-
cable to 12 and 16 bit FATs.
L Sets the length of the FAT.
B Use the bootsector stored in the given file or device, instead
of using its own. Only the geometry fields are updated to
match the target disks parameters.
k Keep the existing boot sector as much as possible. Only the
geometry fields and other similar filesystem data are updated
to match the target disks parameters.
To format a diskette at a density other than the default, you must
supply (at least) those command line parameters that are different
from the default.
Mformat returns 0 on success or 1 on failure.
It doesn't record bad block information to the Fat, use mbadblocks for
that.
See Also
Mtools' texinfo doc
Viewing the texi doc
This manpage has been automatically generated from mtools's texinfo
documentation. However, this process is only approximative, and some
items, such as crossreferences, footnotes and indices are lost in this
translation process. Indeed, these items have no appropriate repre-
sentation in the manpage format. Moreover, not all information has
been translated into the manpage version. Thus I strongly advise you
to use the original texinfo doc. See the end of this manpage for
instructions how to view the texinfo doc.
* To generate a printable copy from the texinfo doc, run the fol-
lowing commands:
./configure; make dvi; dvips mtools.dvi
* To generate a html copy, run:
./configure; make html
A premade html can be found at: 'http://mtools.linux.lu' and
also at: 'http://www.tux.org/pub/knaff/mtools'
* To generate an info copy (browsable using emacs' info mode),
run:
./configure; make info
The texinfo doc looks most pretty when printed or as html. Indeed, in
the info version certain examples are difficult to read due to the
quoting conventions used in info.
mtools-3.9.9 03Mar03 mformat(1)
UNIX/Linux commands referenced on this page: